Switch control mac1/8/2024 ![]() However, this range of multicast address is special and will not be forwarded by an 802.1D-compliant switch. Normally, a frame with a multicast destination sent to a switch will be forwarded out to all other ports of the switch. The particular multicast address used is selected from a range of address which have been reserved by the IEEE 802.1D standard which specifies the operation of switches used for bridging. : Annex 31B.3.3 The use of a well-known address makes it unnecessary for a station to discover and store the address of the station at the other end of the link.Īnother advantage of using this multicast address arises from the use of flow control between network switches. When a station wishes to pause the other end of a link, it sends a pause frame to either the unique 48- bit destination address of this link or to the 48-bit reserved multicast address of 01-80-C2-00-00-01. Only stations configured for full-duplex operation may send PAUSE frames. A media access control (MAC) frame ( EtherType 0x8808) is used to carry the pause command, with the Control opcode set to 0x0001 ( hexadecimal). Pause frame Īn overwhelmed network node can send a pause frame, which halts the transmission of the sender for a specified period of time. The IEEE standard 802.3x was issued in 1997. The first flow control mechanism, the pause frame, was defined by the Institute of Electrical and Electronics Engineers (IEEE) task force that defined full duplex Ethernet link segments. Flow control on Ethernet can be implemented at the data link layer. Using flow control, the receiving station can signal the sender requesting suspension of transmissions until the receiver catches up. Finally, you can turn on the useless Dashboard, either as its own Space or as an overlay.A sending station (computer or network switch) may be transmitting data faster than the other end of the link can accept it. ![]() ![]() By default switching desktops on one display will also switch the other, but with this option checked each display will have it own set of desktops. The option “Displays have separate Spaces” applies to Macs with multiple monitors.The option “Group windows by application,” when checked, ensures that multiple windows from the same application appear side-by-side in Mission Control.The option “When switching to an application, switch to a Space with open windows for the application” ensures that will happen even if the window is on another desktop. When you use Command+Tab to switch applications, you probably also want to switch to an active window.This can be very confusing, so turn off the “Automatically rearrange Spaces based on most recent use” option if you’re constantly losing track of windows. By default Mission Control will organize your spaces automatically, based on what it thinks you want.Here’s a quick breakdown of what these options do: Head to System Preferences, then the Mission Control section.įrom here you’ll find the main options for Mission Control Mission Control mostly works without any configuration, but it’s possible that a few things about it annoy you. This is perfect when you want as much space as possible to work with only two applications, such as when you’re browsing a high-quality website and taking notes. This allows you to run two full screen applications side by side, in what’s called split view mode. Do you know about the full screen button? It’s the green one near the top-left of every window. Full Screen Applicationsīut wait…there’s more. If you want a particular application to always show up on a certain desktop, or even on all desktops, simply right-click its dock icon, then move to the Options submenu.įrom here you can assign an application to a given desktop, or even have it show up on all desktops. These will both switch your desktops immediately, and are a nice compliment to the keyboard and mouse shortcuts I mentioned earlier. It’s a lot faster, however, to use the keyboard shortcuts Control+Right and Control+Left, or to swipe three fingers to the left or the right. To switch between desktops, you could just open Mission Control then click the desktop you want to open. And you can add as many desktops as you like by clicking the “+” button at far right. With multiple desktops you can organize your workflow, allowing you to do things like research on one desktop while you write on another.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |